Home > New & Used Parts
New & Used Parts
New and Used British Seagull outboard motor parts come in all the time and are listed here or on eBay. If you're looking for a particular part not in this list, send me an email, with your outboard serial number, and I'll do our best to assist. Payments may be made via PayPal or money order. Please specify when submitting your email order.
Parts
New Parts
Rubber Storm Cowl (Part No.: 50/1296) - NEW ARRIVAL
Item Description: This rubber storm cowl helps reduce spray that can enter the carburettor. This cowl will fit all outboards equipped with a Villiers carburettor.
Price: $19.99
Order Now
Clutch Unit (Part No.: BSACC99 012) - NEW ARRIVAL
Item Description: Not available.
Price: $19.45
Order Now
Oil Seal Cover (Part No.: BSC40/239) - NEW ARRIVAL
Item Description: Not available.
Price: $6.40
Order Now
Bolt (QB Series) (Part No.: BSCN04 011) - NEW ARRIVAL
Item Description: Not available.
Price: $2.45
Order Now
Coil End Stud (Part No.: BSM1646E) - NEW ARRIVAL
Item Description: Not available.
Price: $126.08 & $14.26
Order Now
Coil Lock Screw (Part No.: BSM2162) - NEW ARRIVAL
Item Description: Not available.
Price: $1.95 (set of two)
Order Now
Cylinder Head (Part No.: BSS100/220) - NEW ARRIVAL
Item Description: Not available.
Price: $46.60
Order Now
Choke Shutter, Screw Washer (Part No.: BSV146x2) - NEW ARRIVAL
Item Description: Not available.
Price: $1.95 (set of two)
Order Now
Piston (Part No.: 50/1296) & Gudgeon Pin (Part No.: 50/1298)
Item Description: This is a new Piston and Gudgeon Pin. This piston fits all 64cc engines, forty plus, forty minus, featherweight and curlew.
Price: $126.08 & $14.26
Email Order
Used Parts
Amal Spray-Proof Air Intake & Choke Control
Item Description: This used Amal Spray-Proof Air Intake & Choke Control is for an Amal 416 model carburettor. It will NOT fit an Amal 2 jet carburettor. The Choke Shutter is broken and will need to be replaced.
Price: Make An Offer > Email Offer
Brass Villiers Carburettor Float (Part No.: V107 x 1)
Item Description: This is a used Brass Float for a Villiers Carburetor. There are a couple small dents but it has been tested for leaks and none were found.
Price: Make An Offer > Email Offer
Flywheel (Part No.: 1265)
Item Description: This flywheel came off engine number: CPC 18081L (Century Plus clutch drive) that had a frozen cylinder. Therefore, it was not been tested.
Price: Make An Offer > Email Offer
Crankcase, Crankshaft & Flywheel key (Part No.: 100/1280/1, S1291A, 1292/W)
Item Description: This Crankcase, Crankshaft & Flywheel key came off engine number: CPC 18081L (Century Plus clutch drive) that had a frozen cylinder. Therefore, it was not been tested.
Price: Make An Offer > Email Offer
Piston (102cc), Gudgeon pin & Connecting rod (Part No.: S1296, S1298, S1294)
Item Description: This Piston, Gudgeon pin & Connecting rod also includes screws for big end bearing and connecting parts and gudgeon pin circlips. It was not been tested.
Price: Make An Offer > Email Offer
Engine Support Lug, complete (Part No.: 1335)
Item Description: This Engine Support Lug (fits all Century & Silver Century models) includes studs (x2) for support lug, cap, spring washers (x2) and brass nuts (x2).
Price: Make An Offer > Email Offer
Bolts for crankcase & nuts x4 (Part No.: 1285, 1287)
Item Description: All forty - Plus, featherweight & minus use four bolts and nuts.
Price: Make An Offer > Email Offer
Bolts for crankcase & nuts x5 (Part No.: 1285, 1287)
Item Description: All century, century plus, silver century and silver century plus, use five bolts and nuts.
Price: Make An Offer > Email Offer
Coverplate for flywheel (Part No.: 1266)
Item Description: This part and the starting pulley were used on engines made during the 1950's and early 1960's. These parts were replaced with a complete pulley plate made of hard plastic.
Price: Make An Offer > Email Offer
Starting Pulley (Part No.: 1267)
Item Description: This part along with the coverplate for flywheel was used on engines made from the 1950's and early 1960's. These parts were replaced with a complete pulley plate made of hard plastic.
Price: Make An Offer > Email Offer
Washer for dome nut (Part No.: 1269)
Item Description: The washer can be used on either the two piece flywheel coverplate and starting pulley or the complete pulley plate made of hard plastic.
Price: Make An Offer > Email Offer
Dome nut for starting-pulley-plate (Part No.: 1268 or M1268)
Item Description: This dome nut is used on most complete pulley plates made of hard plastic.
Price: Make An Offer > Email Offer
Dome nut for starting pulley (Part No.: 1268)
Item Description: This dome nut is used on most metal two piece flywheel coverplate and starting pulley systems.
Price: Make An Offer > Email Offer
Combined Starter-Pulley-Plate (Part No.: M1266/7)
Item Description: This starter-pulley-plate made of hard plastic was made to replace to the two part (1266 & 1267) metal plate and pulley system.
Price: Make An Offer > Email Offer
*When you submit your order/offer form, the cost of shipping will be assessed. Handling is free.